Bronkhorst BRIGHT (V2.00 and higher) User Manual

instruction manual BRIGHT Local colour TFT readout and control module Doc nr.: 9.17.048F Date: 08-05-2014 ATTENTION: Before installing and operat

5 | USER INTERFACE 5.4 Measure readout This area shows the actual flow. The following parameters will affect the format of this readout: o actual

5 | USER INTERFACE The top line will show the USERTAG or the serial number of the connected instrument. 5.8 Edit Setpoint Setpoint can o

5 | USER INTERFACE The button can be used to exit the edit mode and cancel the changes. 5.9 Reset Coun

5 | USER INTERFACE 5.10 Reset Alarm Alarm messages will be shown in the topline of the display and custom readout 2 will be selected autom

5 | USER INTERFACE The button can be used to exit the edit mode and cancel the changes. If you are not intending to reset the alarm, you can press

5 | USER INTERFACE The instrument directly connected with the BRIGHT will be indicated as ‘local’. Other instruments will be indicated with the

5 | USER INTERFACE 9.17.048 Page 16

6 | SETTINGS MENU 6 Settings menu From the readout screen press to enter the settings menu. Press to return to the readout screen. Security se

6 | SETTINGS MENU 6.1 Readout screen From the readout screen you can edit the following settings: o readout format, actual or percentage o fluid

6 | SETTINGS MENU Press again to enter the edit mode of the fluid field. Use or to select one of the available fluidsets. Press to confirm. P

BRONKHORST HIGH-TECH B.V. Disclaimer Even though care has been taken in the preparation and publication of the contents of this manual, we do not assu

6 | SETTINGS MENU 6.5 Controller settings screen From the controller settings screen you can edit the following settings: o setpoint slope time o

6 | SETTINGS MENU The following controller modes can be selected: selection description analog input Setpoint via analog input bus/rs232 Setpoint via

6 | SETTINGS MENU To enter the master slave settings screen, select the master slave option from the controller settings screen and press to enter.

6 | SETTINGS MENU Use the and button to edit each character, press to select the next character. Press to cancel the input and exit the edit m

6 | SETTINGS MENU In the controller response settings screen you can select one of the parameters using the and buttons. Press to enter the edit

6 | SETTINGS MENU 6.12 Set counter mode When entering the counter settings screen, the counter mode is selected. Press to enter the edit mode. Sele

6 | SETTINGS MENU 6.14 Set setpoint at counter limit You can program an automatic setpoint which will be activated when the counter limit is reached.

6 | SETTINGS MENU In the edit mode, use and to change each character. Press to select the next character. Press to exit the edit mode without

6 | SETTINGS MENU 6.16 Set alarm mode When entering the alarm settings screen the alarm mode is selected. Press to enter the edit mode. Select an a

6 | SETTINGS MENU 6.18 Set setpoint at alarm You can program an automatic setpoint which will be activated when an alarm situation occurs. To change

BRONKHORST HIGH-TECH B.V. Table of content 1 SCOPE OF THIS MANUAL ...

6 | SETTINGS MENU When the final character is changed, press to confirm and to exit the edit mode. 6.19 Setup menu Via the setup menu you can: o

6 | SETTINGS MENU 6.21 Change usertag When entering the instrument info screen the usertag parameter is selected. Press to enter the edit mode. In

6 | SETTINGS MENU 6.24 Bus settings When the operating instrument is connected to a bus system you can change the node address of this instrument. Fr

6 | SETTINGS MENU Press to start the sensor auto zero procedure. While the auto zero procedure is active, the BRIGHT will show the message ‘busy’.

7 | SECURITY SETTINGS 7 Security Settings 7.1 Security modes The security settings screen allows you to define the access of the crucial menu item

7 | SECURITY SETTINGS The  or  signs in the upper right corner indicates that you can scroll this menu using the and buttons to select more ite

7 | SECURITY SETTINGS 7.5 Reset Password From the readout screen press both and for 5 seconds till the ‘enter password’ display appears. Again

8 | TROUBLESHOOTING 8 Troubleshooting No output signal • No power supply Check power supply • PCB failure Check cable Return to factory • Valve bl

9 | TECHNICAL DATA 9 Technical Data  1.8” colour TFT display with a 128x160 pixel resolution  100 MHz Processor  15..24Vdc 0.6W Power Consumptio

10 | SERVICE 10 Service For current information on Bronkhorst High-Tech and service addresses please visit our website:  http://www.bronkhorst.com

BRONKHORST HIGH-TECH B.V. 1 Scope of this manual 1.1 Introduction The BRIGHT is a readout and operator module for Bronkhorst digital Mass Flow and P

© 2011 Bronkhorst High-Tech B.V. All rights reserved. This documentation is protected by copyright. Subject to technical and optical changes as w

2 | UNPACKING 2 Unpacking B1 B2 B3 B4     BRIGHT module     Mounting set   - - IP40 T-part - -   IP65 T-part     Short 0.3m

2 | UNPACKING Check the outside packing box for damage incurred during shipment. Should the packing box be damaged, then the local carrier must be n

3 | MOUNTING 3 Mounting ! Take attention to tighten, don’t over tight. ! The BRIGHT comes with 4 different bolts. Please check the instruction

4 | CONNECTING 4 Connecting ! Do not apply pressure until electrical connections are made. ! When providing your own power supply, be sure that

5 | USER INTERFACE 5 User Interface 5.1 Buttons The buttons have the following functions: - Enter selected menu - Enter edit mode - Confirm s